Automotive Transmission Gear: 20CrMnTi Carburizing Case Study
Ein Automobil-Getriebe-Schrägzahnrad – speziell ein Eingangswellenrad, das Motor-Drehmoment durch das Getriebe überträgt. Es muss hohes Drehmoment, hohe Drehzahl und Stoßbelastung gleichzeitig bewältigen. Das Zahnradprofil, die Werkstoff-Wärmebehandlung und die Oberflächenrauheit sind alle kritisch für Lärm, Haltbarkeit und Effizienz. Hier ist der vollständige Fertigungsansatz.
Projektueberblick
Schluesselparameter
| Item | Spec |
|---|---|
| Anwendung | Transmission input shaft gear (helical) |
| Material | 20CrMnTi alloy steel (GB/T 3077) |
| Module | 2.5 |
| Number of Teeth | 32 |
| Pressure Angle | 20° |
| Face Width | 28 mm |
| Tooth Surface Hardness | HRC 58–62 (carburized) |
| Core Hardness | HRC 30–35 |
| Annual Volume | 5,000 – 50,000 pcs/year |
Critical Dimensions
| Merkmal | Toleranz |
|---|---|
| Gear quality grade | DIN 5–6 (ISO 1328) |
| Tooth profile accuracy | ±0.005 mm |
| Pitch accuracy | ±0.008 mm |
| Runout (gear bore reference) | ≤ 0.01 mm |
| Bore diameter (shaft fit) | H7 (+0.021 / 0) |
| Case depth (carburized) | 0.8–1.2 mm |
| Spline dimensions | Per customer spline spec |
1. Material Selection: Carburizing Steels Compared
Getriebezahnräder erfordern eine spezifische Kombination von Eigenschaften: eine harte, verschleißfeste Zahnoberfläche und einen zähen Kern, der Stoßlasten während Schaltvorgängen aufnehmen kann. Einsatzhärten – Kohlenstoff bei hoher Temperatur in die Randschicht diffundieren, dann abschrecken – ist der Standardansatz. Der Basiskohlenstoff bestimmt, wie gut dieser Prozess funktioniert und wie das fertige Zahnrad performt. Vier gängige Legierungsstähle werden unten verglichen.
| Material | Carburizing Response | Core Toughness | Surface Hardness (Post-Carburize) | Machinability (Pre-Heat-Treat) | Cost Index |
|---|---|---|---|---|---|
| 20CrMnTi | Excellent -- uniform case depth, Ti refines grain | Good -- adequate for shift shock | HRC 58–62 | Good -- comparable to 4140 | 1.0x |
| 20CrMo | Good -- Mo improves hardenability | Good -- similar core toughness | HRC 56–60 | Gut | 1.1x |
| 40Cr | Fair -- higher carbon content, risk of retained austenite in case | Moderate -- through-hardening steel, core can be brittle | HRC 55–58 | Gut | 0.9x |
| 8620H | Very good -- Ni improves toughness | Very good -- best core impact resistance here | HRC 58–62 | Fair -- slightly tougher to machine | 1.4x |
Why 20CrMnTi is the standard for automotive gears in China and Asia: The titanium addition in 20CrMnTi pins grain boundaries during carburizing, preventing excessive grain growth at the 920°C carburizing temperature. This produces a fine-grained case with consistent hardness -- a practical advantage in production. The material is widely available from Chinese steel mills, well-understood by heat treatment shops, and priced competitively. For most passenger-car transmission gears, it provides the right balance of performance and cost.
2. Why 20CrMnTi for This Application
20CrMnTi (GB/T 3077) is a low-carbon alloy steel containing approximately 0.17–0.23% C, 0.80–1.10% Cr, 0.80–1.10% Mn, and 0.04–0.10% Ti. It is the de facto standard material for automotive transmission gears manufactured in China and much of Asia. The rough Western equivalent is 20MnCr5 (DIN EN 10084), though the titanium addition in 20CrMnTi gives it distinct grain-refining behavior during high-temperature carburizing.
| Eigenschaft | Value | Design Implication |
|---|---|---|
| Dichte | 7.85 g/cm³ | Standard steel density |
| Tensile Strength (pre-heat-treat) | 800–1100 MPa | Adequate for handling and fixturing before carburizing |
| Surface Hardness (post-carburize) | HRC 58–62 | Resists tooth flank wear and pitting under Hertzian contact stress |
| Core Hardness (post-carburize) | HRC 30–35 | Absorbs impact loads during gear shifts without cracking |
| Effective Case Depth | 0.8–1.2 mm | Sufficient for module 2.5 gear tooth loading |
| Carburizing Temperature | 920 °C | Standard temperature for this material |
| Grain Size (post-carburize) | 6–8 (ASTM) | Ti addition prevents grain coarsening at temperature |
Carburizing Depth Control
The case depth must match the applied load. Bei einem Modul-2.5-Rad liegt die maximale Hertzsche Pressung etwa 0.5–0.7 mm unter der Zahnflanke. A case depth of 0.8–1.2 mm provides adequate support beneath this stress zone while keeping the transition gradient manageable. Ist die Randschicht relativ zur einwirkenden Last zu dünn, kann Scherspannung unter der Oberfläche zu Ausbrüchen (Spalling) führen — Stücke der gehärteten Randschicht platzen unter Last ab. Ist die Randschicht zu dick, wandert die Übergangszone näher zum Kern, und der Werkstoff wird insgesamt spröder.
Why not through-hardening steels? Through-hardening steels like 40Cr or 45# achieve uniform hardness throughout the cross-section. While the tooth surface is hard enough, the core is equally brittle. Unter den Stoßbelastungen, wie sie beim Gangwechsel auftreten, neigt ein durchgehärtetes Zahnrad eher zu Zahnbrechung — der Riss beginnt am Fußrundungsradius und breitet sich durch den spröden Kern aus. Carburized gears maintain a tough core that arrests crack propagation. This is the fundamental reason carburizing is preferred for transmission gears.
3. Machining Strategy
3.1 The Core Challenge: Heat Treatment Distortion
Every thermal operation -- carburizing at 920°C, oil quenching, tempering -- introduces dimensional change. Gears grow, warp, and distort. The amount of distortion depends on geometry (thin-walled gears distort more than solid blanks), fixturing during heat treatment, and quench severity. The key insight is that you cannot prevent distortion entirely -- you must plan for it by leaving grinding stock after rough machining.
3.2 Recommended Process Chain
- Blank preparation: Forged or hot-rolled 20CrMnTi bar stock, turned to blank diameter on a CNC lathe. Bore is rough-machined to leave stock for finish grinding. Face surfaces are also left with grinding allowance.
- Gear hobbing (rough): Cut gear teeth using a CNC gear hobbing machine. This is the roughing operation -- leave 0.15–0.20 mm per flank as grinding stock. Tooth profile at this stage is DIN 7–8, intentionally loose to allow for post-heat-treat correction.
- Einsatzhärten und Abschrecken: 920 °C für 6–8 Stunden (Gasmuffelofen mit Kontrollatmosphäre und Kohlenstoffpotenzial-Überwachung), Ölabschreckung zum Härten der Randschicht, Anlassen bei 180 °C für 2 Stunden zum Abbau der Abschreckspannungen und zur Reduzierung des Restaustenits. Die Teile werden auf dedizierten Hearth-Plates fixiert oder hängend vertikal eingespannt, um Verziehung zu minimieren.
- Gear grinding (finish): The most critical and expensive operation. CNC gear grinding machine removes the 0.15–0.20 mm per flank to final DIN 5–6 profile accuracy. Generating grinding (continuous) or form grinding (single-index) depending on gear geometry and volume. This operation corrects the heat treatment distortion and achieves the final tooth geometry.
- Spline broaching: Internal or external splines for shaft connection are broached after heat treatment. Broaching is preferred because the hardened case is too hard for conventional cutting tools. If splines are internal, they may be broached before carburizing if the spline walls are thin enough to carburize through.
- Deburring: Remove all burrs from tooth edges, bore edges, and spline features. Vibratory finishing or manual deburring. Burrs left on tooth flanks become stress concentrators under load and initiate pitting.
- Final inspection: Gear measuring machine for tooth profile, pitch, and runout. Hardness testing, metallographic examination, dimensional CMM. First article inspection per PPAP requirements.
Distortion is predictable, not random. For a given gear geometry and fixturing method, the distortion pattern is consistent from batch to batch. Experienced shops track distortion data across batches and compensate the hobbing cutter geometry accordingly. If a particular gear consistently shows 0.03 mm of bore shrinkage after carburizing, the pre-heat-treat bore is machined 0.03 mm oversize. This compensation approach reduces grinding time and improves process capability.
4. Quality Testing
| Prüfung | Methode | Kriterium | Häufigkeit |
|---|---|---|---|
| Gear profile (tooth form) | Gear measuring machine (CNC) | ISO 1328 Grade 5–6: profile error fα ≤ 6–8 μm, helix error fβ ≤ 5–7 μm | First article + 2 pcs/shift |
| Pitch error | Gear measuring machine | ISO 1328 Grade 5–6: cumulative pitch Fp ≤ 20–28 μm | First article + 2 pcs/shift |
| Runout | Gear measuring machine | ≤ 0.01 mm (radial runout, bore reference) | First article + 2 pcs/shift |
| Surface hardness (HRC) | Rockwell hardness tester | HRC 58–62 on tooth flank | Per heat treat batch (3 pcs) |
| Case depth (metallographic) | Cross-section, microhardness traverse | Effective case depth 0.8–1.2 mm (HV 550 cutoff) | Per heat treat batch (1 pc destructive) |
| Core hardness | Rockwell hardness tester | HRC 30–35 (at mid-tooth or core location) | Per heat treat batch (3 pcs) |
| Noise test | Gear rolling tester (single flank) | Transmission error within spec, no abnormal gear whine | First article + periodic |
| Dimensional (CMM) | Coordinate measuring machine | All critical dimensions per drawing | First article + 5 pcs/shift |
First article inspection per PPAP: Für IATF-16949-konforme Produktion muss der Erstmusterprüfbericht vollständige Getriebemetrologie enthalten (Profil, Flankenlinie, Teilung, Rundlauf), Härtewerte (Rand und Kern), Metallografie der Aufhärtungstiefe sowie dimensionelle CMM-Daten. All results are documented in the PPAP Production Part Submission Warrant (PSW). Der Kunde verlangt typischerweise eine vollständige Erstbemusterung über 3–5 aufeinanderfolgende Teile, bevor er die Produktion freigibt.
5. Cost Drivers: Where the Money Goes
| Kostentreiber | % of Unit Cost | Notes |
|---|---|---|
| Raw material (20CrMnTi forging/bar) | 10–15% | Forged blanks preferred for gear blanks -- better grain flow and less machining stock than bar stock. Material cost is moderate; 20CrMnTi is a standard grade widely produced in China. |
| Gear hobbing (rough) | 15–20% | CNC gear hobbing machine with carbide hobs. Cycle time depends on module, number of teeth, and face width. For module 2.5 / 32 teeth / 28 mm face width, expect 3–5 minutes per part. |
| Heat treatment (carburizing + quench + temper) | 15–20% | Controlled atmosphere furnace with carbon potential monitoring. Oil quench. 6–8 hour cycle at 920 °C. Batch process -- cost per part drops with batch size. |
| Gear grinding (finish) | 20–25% | The most expensive single operation. CNC gear grinding machine removes 0.15–0.20 mm per flank. Cycle time 8–15 minutes per part depending on gear size and required accuracy. Grinding wheel wear and dressing add to cost. |
| Spline broaching | 5–8% | Broach tool is a significant upfront cost ($2,000–8,000) but per-part cost is low. Amortized over production volume. |
| Inspection and metrology | 10–15% | Gear measuring machine time is the main cost. First article inspection requires extensive documentation. Ongoing SPC requires periodic gear metrology checks. |
| Tooling and gauges | 5–10% | Hob cutters, grinding wheels, broach tools, inspection gauges. Hob cost $800–2,000, grinding wheels $200–500. Spread over production volume. |
What drives cost: Gear grinding is the most expensive single operation, typically accounting for 20–25% of unit cost. Die Schleifzeit hängt direkt vom abzutragenden Aufmaß und der geforderten Genauigkeit ab. Tighter tolerances (DIN 5 vs DIN 6) increase grinding time by 30–50%. The largest cost reduction lever is controlling heat treatment distortion -- less distortion means less grinding stock, which means shorter grinding cycles. Investment in fixturing and process control upstream pays off in reduced grinding cost downstream.
6. Common Mistakes That Reduce First-Article Yield
1. Insufficient grinding stock after heat treatment. Ist das Schleifaufmaß (0.15–0.20 mm pro Flanke) kleiner als die tatsächliche Verziehung aus Einsatzhärten und Abschrecken, kann das Schleifen das Zahnprofil nicht auf die geforderte DIN-5–6-Genauigkeit aufreiben. Das Ergebnis ist ein Teil, das dimensionale Prüfungen punktuell besteht, aber Bereiche aufweist, in denen die Randschicht vollständig verschliffen wurde und der weichere Kern freiliegt. Track distortion data from the first batch and adjust grinding stock accordingly. For a new gear geometry, start with 0.20 mm per flank and reduce once the distortion pattern is understood.
2. Wrong carburizing depth. Zu dünn (unter 0.8 mm bei Modul 2.5): Die Randschicht kann die Hertzsche Pressung nicht aufnehmen — Rissbildung unter der Oberfläche führt unter Last zu Ausbrüchen. Zu dick (über 1.2 mm): Die Übergangszone wandert nach innen, das Zahnrad wird spröder und verliert die Fähigkeit, Stöße zu absorbieren. The case depth must be specified as effective case depth (ECD) at the HV 550 cutoff, measured by microhardness traverse on a destructively tested sample -- not estimated from time and temperature alone.
3. Skipping noise testing. A gear can pass all dimensional and hardness checks and still produce unacceptable noise in the vehicle. Gear noise (whine) is caused by transmission error -- the deviation of the actual tooth contact pattern from the theoretical ideal. Kleine Abweichungen in Zahnprofil oder Flankenlinie, die innerhalb der DIN-5–6-Toleranzbandbreite liegen, können bei bestimmten Drehzahlen dennoch ein hörbares Heulen erzeugen. Einflanken-Wälzprüfungen auf einem Getriebeprüfstand sind die Standardmethode, um dies zu erkennen, bevor die Teile in die Montage gehen.
4. Inadequate deburring. Machining burrs on tooth edges, root fillets, or spline features become stress concentrators under cyclic loading. In service, these burrs can cause micro-cracking that progresses to pitting or tooth breakage. Burrs are particularly problematic on the tooth root fillet -- the area of highest bending stress. Vibratory finishing or manual deburring under 10x magnification should be a standard step before final inspection.
5. Not compensating for heat treatment distortion in fixture design. Räder, die beim Einsatzhärten einfach flach auf einer Ofen-Hearth-Plate liegen, verziehen sich ungleichmäßig — die Unterseite kühlt beim Abschrecken schneller und zieht sich unterschiedlich zusammen. Dedicated fixturing (vertical hanging fixtures, or constrained fixtures that allow uniform quench flow) reduces distortion significantly. The fixture design should account for the gear geometry: thin-faced gears need support to prevent warpage; gears with asymmetric features need balanced quench flow. Fixture development is part of the process engineering, not an afterthought.
7. Production Timeline
| Phase | Dauer | Lieferobjekt |
|---|---|---|
| DFM review and quotation | 3–5 days | Updated drawing with DFM notes, material and heat treatment confirmation, formal quote |
| Fixture design and manufacture | 7–10 days | Hobbing fixtures, heat treatment fixtures, grinding fixtures, broach tools, inspection gauges |
| First-article machining (hobbing + carburizing + grinding) | 7–10 days | 5–10 FAI parts, in-process dimensional reports at each stage |
| First-article testing and metrology | 3–5 days | Full gear metrology (profile, helix, pitch, runout), hardness, case depth metallography, noise test |
| PPAP documentation | 5–7 days | PSW, control plan, PFMEA, MSA studies, material certs, dimensional layout |
| PPAP review and approval | 3–5 days | Customer review and sign-off on PPAP package |
| Total (DFM to PPAP approval) | 5–7 weeks | Approved for production |
Prototype lead time: For prototype quantities (5–20 parts) without full PPAP documentation, lead time is typically 10–14 days. Dies setzt voraus, dass Material am Lager ist und die Zahnradgeometrie innerhalb der Standard-Wälzfräsfähigkeiten liegt. Production lead time after PPAP approval is 4–6 weeks, depending on order quantity and current production schedule.
Über diese Fallstudie
Diese technische Analyse basiert auf einem Kfz-Getriebezahnradprogramm bei Sinbo Precision. Konkrete Kundendetails, exakte Teilnummern und proprietäre Konstruktionsmerkmale wurden geändert oder weggelassen. Alle Prozessparameter, Werkstoffdaten und Toleranzwerte sind repräsentativ für typische Anforderungen an Getriebezahnräder für Kraftfahrzeuge.
Verwandte Werkstoffe · Verwandte Leistungen · Verwandte Fallstudien
Verwandte Werkstoffe: Steel
Verwandte Leistungen: Cnc Machining
Verwandte Fallstudien: Precision Robot Parts · Automotive Second Source
Need a Quote for Automotive Transmission Gears?
Send us your drawing -- we'll return a DFM review and quote within 3 business days.
Angebot anfordern →